Power drills?

For all your modelling and painting discussions
Post Reply
ianjgow
Posts: 17
Joined: Wed Nov 13, 2013 2:53 pm

Power drills?

Post by ianjgow »

Can anyone recommend a reasonable power drill (do I need vari-speed?) that will take small drillbits ~ 0.5 01 1mm suitable for simple conversion work like drilling out weapons to replace with wire & changing arms/heads etc?

Cheers!

i (too many blisters from my hand drill)
User avatar
Norm
Posts: 276
Joined: Thu Apr 24, 2014 7:45 pm

Re: Power drills?

Post by Norm »

Dremel seems to be the 'best', as i understand it, it has a low speed setting of 300 rpm, which is meant to be the modellers friend.

I use the cheaper Draper 140w multi-tool but the lowest speed is 10000 rpm or 15000 rpm (the information with the machine conflicts on the point) and while I like it, I think it probably runs too fast and therefore the bit gets too hot and I end up with molten metal clogging the bit.
curlerman
Posts: 35
Joined: Wed Jan 08, 2014 2:54 pm

Re: Power drills?

Post by curlerman »

Norm wrote:Dremel seems to be the 'best', as i understand it, it has a low speed setting of 300 rpm, which is meant to be the modellers friend.

I use the cheaper Draper 140w multi-tool but the lowest speed is 10000 rpm or 15000 rpm (the information with the machine conflicts on the point) and while I like it, I think it probably runs too fast and therefore the bit gets too hot and I end up with molten metal clogging the bit.
I second this suggestion Dremel is the way to go. I would be lost without mine. Be careful however there are two low speed versions . The cheaper one is not a good option. theres a slightly more expensive one with 5 or 6 speed sttings both slower and faster than the other. that's my choice.
Winning is not a priority for gamers but losing is a definite no-no

web:- http://www.angelfire.com/games4/bobsgam ... urlers.htm
blog :- http://flownlegions.blogspot.com.es/
User avatar
Paul K
Posts: 405
Joined: Tue Oct 08, 2013 11:34 am
Contact:

Re: Power drills?

Post by Paul K »

At the moment for the smaller drill sizes of 2mm or less I use a 'pin chuck' which then fits into the normal chuck of my small power drill. It makes for a cheap yet very effective small drill tool compared to some of the Dremels, which although good, are quite expensive.
Kind regards
Paul

Image
http://www.kallistra.co.uk
Nick Huge
Posts: 2
Joined: Sun Jul 27, 2014 9:06 pm

Re: Power drills?

Post by Nick Huge »

All round the dremel is the pick of the bunch.
Pin chuck drills can be perfect for the most delicate work and when i need to make a hole quickly I go for my 12 volt cordless battery drill and then tidy up with a dremel.
Dremels are pricey but awesome.
User avatar
von Klinkerhoffen
Posts: 76
Joined: Mon Nov 18, 2013 5:04 pm

Re: Power drills?

Post by von Klinkerhoffen »

I would not recommend using a power drill for such small models, mainly because of the torque and because if you slip the drill will not stop? Also, the drill bit can 'stick' and with a small drill bit it will snap off leaving the drill bit embedded in the model!

I am with Paul on this one and would recommend a 'pin vice' with which you will have more control.

You can buy an "Archimedes Small Hand Drill" for £3.99 each at:
http://www.tickintimeworldofwatchtools. ... s-33-p.asp

I find these useful and try and avoid using my Dremmel on small models.

Apologies if this breaches any forum rules?
von Klinkerhoffen
Well tally ho! With a bing and a bong and a buzz buzz buzz!
curlerman
Posts: 35
Joined: Wed Jan 08, 2014 2:54 pm

Re: Power drills?

Post by curlerman »

von Klinkerhoffen wrote:I would not recommend using a power drill for such small models, mainly because of the torque and because if you slip the drill will not stop? Also, the drill bit can 'stick' and with a small drill bit it will snap off leaving the drill bit embedded in the model!
You are right in saying this is a possibility BUT it's a matter of practice I not only use my dremel on ten mil figures but I drill down to 0.35mm bits with it. It's a question of speed and steadiness. For instance I replace ALL the spears on my figures and can easily drill a 0.4mm hole in a hand to receive a 0.33mm brass spear. You can see the results in the dark age section of my blog. My advice is be brave, stock up on drill bits and give it a try. drilling the hands of 50 or 60 figure with a pin chuck is painfully slow! :D :) ;)
Winning is not a priority for gamers but losing is a definite no-no

web:- http://www.angelfire.com/games4/bobsgam ... urlers.htm
blog :- http://flownlegions.blogspot.com.es/
User avatar
von Klinkerhoffen
Posts: 76
Joined: Mon Nov 18, 2013 5:04 pm

Re: Power drills?

Post by von Klinkerhoffen »

If you get on with using a Dremel - well done.

I presume you have the Dremel held in a drill stand or bench vice? Just the weight of the drill would snap a 0.35mm drill bit.
I mention this out of curiosity and to advise any beginner to be careful.

I would also STRONGLY advise the wearing of protective eye wear if anyone does this.

Any way, thanks for the update curlerman I think I will stick with using a pin vice ;)
von Klinkerhoffen
Well tally ho! With a bing and a bong and a buzz buzz buzz!
curlerman
Posts: 35
Joined: Wed Jan 08, 2014 2:54 pm

Re: Power drills?

Post by curlerman »

von Klinkerhoffen wrote:
I presume you have the Dremel held in a drill stand or bench vice? Just the weight of the drill would snap a 0.35mm drill bit.
I mention this out of curiosity and to advise any beginner to be careful.


No I wing it free style. I hold the model on the table with pliers and then lay my right hand on the table with a book or whatever to get it supported on the table with the drill in it at the right height. Yes I broke quite a number of drills in the early days but with practice I haven't broken a drill in months. Also freestyle lets you "feel" the stresses on the drill bit.
Winning is not a priority for gamers but losing is a definite no-no

web:- http://www.angelfire.com/games4/bobsgam ... urlers.htm
blog :- http://flownlegions.blogspot.com.es/
Post Reply